We're Proud of the Work that Erik Does in Warren

I was hired to perform a tune-up on a furnace. The furnace was not producing heat properly, and the pilot light was not staying lit. I inspected the furnace and found that the gas valve was not opening, which was causing the issue. I replaced the gas valve and tested the furnace to ensure it was working properly. I also cleaned the burners and inspected the flue for any blockages. The furnace is now producing heat properly, and the pilot light is staying lit.

I am a skilled professional that works for a McCarver Mechanical Heating & Cooling company. I recently completed a job replacing an air vent in a residential home. The vent was old and leaking, so it needed to be replaced. I removed the old vent and installed a new one, ensuring that it was properly sealed and connected to the ductwork. I also cleaned up the area and made sure that the new vent was operating correctly. The customer was very satisfied with the work, and I was proud to have been able to help them with their heating and cooling needs.

I was hired to perform maintenance on a residential air conditioner. I arrived at the job site and inspected the unit to determine the problem. I then removed the old air filter and replaced it with a new one. I also cleaned the condenser coils and checked the refrigerant levels. Finally, I tested the unit to ensure it was working properly.

I am a skilled professional that works for a McCarver Mechanical Heating & Cooling company. I recently completed a job where I performed maintenance on a combo boiler. The boiler was a large, complex system that provided heating and hot water to a large commercial building. During the maintenance, I inspected the boiler for any signs of wear or damage. I replaced the burner, cleaned the heat exchanger, and adjusted the pressure relief valve. I also checked the electrical connections and tested the safety controls. After the maintenance was complete, I performed a thorough test of the boiler to ensure that it was operating correctly. I recorded the results of the test and provided a report to the building owner. Overall, the maintenance job was successful, and the boiler is now operating at peak efficiency. I am proud of the work that I did and look forward to completing more jobs in the future.

I was hired by a local HVAC contractor to perform a check-up on a furnace. The furnace was located in a residential home and had been experiencing issues with heating. During the check-up, I inspected the furnace for any signs of damage or wear and tear. I checked the thermostat, the blower motor, the air filter, and the combustion chamber. I also checked the gas line and the electrical connections. If any issues were found, I would recommend a repair or replacement of the furnace. I would provide a detailed estimate of the cost of the repair or replacement and answer any questions that the homeowner may have. After the check-up, I cleaned up the area and left the furnace running to ensure that it was working properly. I also provided the homeowner with a maintenance checklist to help them keep their furnace in good working condition. Overall, performing a check-up on a furnace is a critical part of maintaining a home's heating system. It can help prevent costly repairs and ensure

I was hired by a company to perform a tune-up on a boiler. The boiler was not producing the desired amount of heat, so I diagnosed the issue and replaced the necessary parts. I also checked the pressure and temperature of the boiler to ensure it was operating at the correct levels.

I was called to a home to replace a low water cutoff. The homeowner had noticed that their water pressure had been dropping and that their sprinklers were not working properly. I arrived at the home and inspected the low water cutoff. It was clear that it was not working properly, so I replaced it with a new one. I then tested the sprinklers to ensure that they were working properly. The homeowner was very pleased with the work that I had done and thanked me for my help.

I was tasked with replacing the expansion tank on a boiler at a commercial building. The tank was leaking, and the building's occupants were complaining of low water pressure. I removed the old tank and replaced it with a new one, ensuring that it was properly sized and installed. I also checked the pressure relief valve and made any necessary adjustments. Finally, I tested the system to ensure that it was working properly.

I was called to a home to perform a tune-up on a furnace. The furnace was not working properly, and the homeowner was concerned that it would break down during the winter. I arrived at the home and performed a thorough inspection of the furnace. I checked the burners, the blower, the thermostat, and the electrical connections. I also cleaned the furnace and replaced the air filter. After the tune-up, the furnace was working properly, and the homeowner was happy with the results.

I was called to a client's home to perform a tune-up on their steam boiler. The boiler had been running poorly, and the client was experiencing issues with hot water and heating. Upon arrival, I inspected the boiler and found that it was not producing enough heat. I performed a thorough tune-up, including cleaning the burners, adjusting the pressure, and replacing any worn or damaged parts. After the tune-up, the boiler was running smoothly and efficiently, and the client was happy with the results. I also provided the client with tips on how to maintain the boiler and prevent future issues. Overall, the job was successful, and the client was pleased with the results.

I am a skilled professional that works for a McCarver Mechanical Heating & Cooling company. I recently completed a job where I performed a tune-up on a water heater. This involved inspecting the unit for any potential issues, cleaning the burner, and replacing any worn-out parts. I also checked the pressure relief valve and thermostat to ensure they were working properly. After completing the tune-up, I tested the unit to make sure it was operating correctly.

I was called to a home to inspect a furnace that was not heating the home. Upon arrival, I noticed that the condensate drain was clogged. I used a plumbing snake to clear the drain and then used a wet/dry vacuum to remove the debris. After the drain was cleared, the furnace was able to heat the home again.

I was called to a home to perform a tune-up on a furnace. Upon arrival, I found that the furnace was not producing heat as it should. I checked the thermostat and found that it was set to "off." I reset the thermostat and tested the furnace again. It was still not producing heat, so I checked the gas line and found that it was not getting gas. I checked the gas valve and found that it was not getting gas. I replaced the gas valve and tested the furnace again. It was now producing heat. I tested the thermostat and found that it was working properly. I also checked the air filter and found that it was dirty, so I replaced it. I tested the furnace again and it was now producing heat. The homeowner was happy that the furnace was now working properly.

I was called to a home to perform a tune-up on a furnace. The furnace was not working properly, and the homeowner was concerned about the cost of repairs. I arrived at the home and inspected the furnace. I found that the furnace was not producing heat, and the pilot light was not lit. I checked the gas line and found that it was not connected properly. I repaired the gas line and lit the pilot light. I then tested the furnace to ensure that it was working properly. The furnace was working properly, and the homeowner was happy with the service.

I was called to inspect a leaking boiler pipe in a residential building. Upon arrival, I observed that the pipe was leaking from a joint. I carefully removed the old pipe and replaced it with a new one, ensuring a tight seal. I also checked the other joints in the pipe for any signs of wear or damage and made the necessary repairs. Finally, I tested the pipe to ensure it was functioning properly.

I was called to a home to perform a tune-up on a furnace. The furnace was not working properly, so I diagnosed the issue and replaced the faulty parts. I also cleaned the furnace and checked the air filters to ensure they were clean and in good condition. After completing the tune-up, the furnace was working properly again, and the customer was happy with the results.

I am a highly skilled HVAC contractor professional. I recently completed a job where I performed an inspection on a furnace blower motor. The blower motor was not working properly, so I diagnosed the issue and replaced the motor. I also checked the electrical connections and wiring to ensure they were in good condition. After completing the job, I tested the furnace to ensure it was working properly. I am proud of the work I did and the satisfaction of my customers.

I am a skilled professional that works for a McCarver Mechanical Heating & Cooling company. I was assigned to perform an inspection on a leaking evaporator pan in a residential home. The pan was located in the basement and was leaking water onto the floor. I used a flashlight to inspect the pan and found that it was cracked and had rusted. I removed the old pan and replaced it with a new one, ensuring that it was properly sealed and installed. I also cleaned up the area and made sure that the floor was dry before leaving the job site.

I was called to a home to perform a tune-up on a furnace. Upon arrival, I checked the unit's electrical connections, cleaned the burners, inspected the blower, and tested the thermostat. I also checked the air filter and replaced it if necessary. Finally, I tested the furnace to ensure it was operating properly.

I was called to a home to perform maintenance on a steam boiler. The boiler was not producing enough heat, and the customer was concerned that it would not be able to heat the home. I arrived at the home and inspected the boiler. I found that the boiler was not producing enough heat because the pilot light was not lit. I lit the pilot light and then checked the pressure and temperature of the boiler. The pressure was low, and the temperature was too low. I adjusted the pressure and temperature and then tested the boiler again. The boiler was now producing enough heat to heat the home. The customer was very happy with the service and thanked me for my help.

I recently completed a residential furnace tune-up for a customer. This involved inspecting the furnace for any potential issues, cleaning the burners, inspecting the blower, and adjusting the thermostat. I also replaced the air filter and checked the electrical connections. The customer was very satisfied with the results and expressed that their furnace was running more efficiently than ever before.

I was called to a home to perform a tune-up on a boiler. The boiler was not producing enough heat, and the homeowner was concerned that it might need to be replaced. I inspected the boiler and found that the pilot light was out. I relit the pilot light and adjusted the gas pressure. The boiler was now producing enough heat to meet the homeowner's needs.

I am a skilled professional that works for a McCarver Mechanical Heating & Cooling company. I recently completed a tune-up on a furnace. The tune-up involved cleaning the furnace, checking the burners, and replacing the air filter. I also checked the thermostat and made any necessary adjustments. After the tune-up, the furnace was running efficiently and effectively.

I am a professional HVAC technician, and I recently completed an inspection on a residential AC unit. The inspection was part of a routine maintenance service that I provide to my clients. During the inspection, I checked the unit's electrical connections, inspected the refrigerant levels, and tested the unit's airflow and temperature. I also cleaned the unit's coils and inspected the condenser and evaporator fins for any signs of damage. After the inspection, I provided my client with a detailed report of my findings and recommendations for any necessary repairs or maintenance.

I am a highly skilled and experienced home service professional. I recently completed a tune-up on a residential furnace. This involved cleaning the burners, checking the ignition system, and adjusting the gas pressure. I also replaced the air filter and inspected the blower motor and blower wheel for any signs of wear. After the tune-up, the furnace was running efficiently and effectively, providing heat to the home.