We're Proud of the Work that Erik Does in Warren

I was hired to perform a tune-up on three furnaces. I started by checking the electrical connections and replacing any worn or damaged parts. I then cleaned the burners, inspected the gas pressure, and tested the thermostat. Finally, I performed a safety check to ensure that the furnace was operating correctly.

I was hired to perform maintenance on a residential air conditioning unit. I arrived at the customer's home and began by inspecting the unit to identify any issues. I checked the refrigerant levels, cleaned the condenser coils, and replaced the air filter. I also tested the unit's electrical components to ensure they were working properly. After completing the maintenance, I provided the customer with a detailed report of my findings and recommendations for future maintenance.

I am a skilled professional that works for a McCarver Mechanical Heating & Cooling company. I recently completed a job that involved performing maintenance on a residential air conditioning unit. The job required me to inspect the unit, replace the air filter, clean the condenser coils, and check the refrigerant levels. I also tested the unit's electrical components to ensure they were working properly. After completing the maintenance, I provided the customer with a detailed report of my findings and recommendations for future maintenance.

I am a highly skilled HVAC contractor professional. I recently completed a job where I performed maintenance on a mini split. The mini split was installed in a small room and was not working properly. I diagnosed the issue and replaced the faulty compressor. I also cleaned the condenser and evaporator coils and checked the refrigerant levels. After completing the maintenance, the mini split was working perfectly. The client was very happy with the results and thanked me for my work.

I was called to inspect a split system's thermostat. The system was not cooling properly, and the customer suspected that the thermostat was the issue. I arrived at the customer's home and checked the thermostat. I found that the thermostat was not reading the temperature correctly. I replaced the thermostat and tested it to ensure it was working properly. The customer was happy with the service and thanked me for my help.

I was called to replace a capacitor on a residential air conditioner. I arrived at the job site and found that the capacitor was not working properly. I removed the old capacitor and replaced it with a new one. I then tested the system to ensure that the air conditioner was working properly.

I was called to replace a capacitor on a condenser unit. The condenser unit was located on the roof of a commercial building. I used a ladder to access the unit and removed the old capacitor. I then installed the new capacitor and secured it in place. I tested the unit to ensure it was working properly and then cleaned up the work area.

I was hired to perform a leak seal on a residential air conditioner. The job involved removing the old sealant, cleaning the surface, and applying a new sealant to ensure proper insulation and prevent leaks. I used specialized tools and techniques to ensure a high-quality finish and to meet the customer's expectations. The job required careful attention to detail and a strong understanding of the air conditioner's system. I also took the time to explain the process to the customer and answer any questions they had. Overall, the job was successful, and the customer was satisfied with the results.

I was called to a residential home to perform maintenance on a residential furnace. Upon arrival, I found that the furnace was not producing heat. I diagnosed the issue as a faulty thermostat and replaced it with a new one. After completing the repair, I tested the furnace to ensure it was working properly. The homeowner was pleased with the service and thanked me for my help.

I was tasked with performing maintenance on a residential furnace. I started by checking the electrical connections and replacing any damaged wires. I then cleaned the burners and inspected the gas valve for any issues. Finally, I tested the furnace to ensure it was operating correctly.

I am a skilled professional that works for a McCarver Mechanical Heating & Cooling company. I recently completed a tune-up on a residential furnace. This tune-up involved inspecting the furnace for any potential issues, cleaning the burners, checking the thermostat, and lubricating the motor. I also checked the air filter and replaced it if necessary. After the tune-up, the furnace was running efficiently and effectively, providing warm and comfortable air to the home.

I was hired to replace a faulty contactor on an air conditioner. The contactor is a small electrical switch that controls the power flow to the compressor in the air conditioner. It was located in a hard-to-reach area, so I had to remove some panels to access it. Once I removed the old contactor, I installed the new one and connected the wires. I then tested the air conditioner to ensure it was working properly.

I am a highly skilled and experienced home service professional. I recently completed a job on a tankless water heater. The tankless water heater is a great alternative to traditional water heaters because it provides an endless supply of hot water on demand. The job involved removing the old water heater and installing the new tankless water heater. I also performed a thorough inspection of the plumbing system to ensure that it was in good working condition. I replaced the old water heater with a new tankless water heater, connected the gas line, and tested the system to ensure that it was working properly. I also cleaned up the work area and disposed of the old water heater properly.

I was working as an HVAC contractor and was called to a job to clear a drain on a condensate pan. The condensate pan is a small container that collects water from the air conditioner's cooling process. The drain was clogged with debris, including leaves, dirt, and other organic matter. To clear the drain, I used a plumbing snake to remove the blockage. The snake is a flexible wire that is inserted into the drain and rotated to break up the debris. Once the blockage was removed, I flushed the drain with a mixture of water and vinegar to remove any remaining debris. After clearing the drain, I tested the air conditioner to ensure that it was working properly. The condensate pan should be cleaned regularly to prevent the accumulation of debris and ensure that the air conditioner is operating efficiently.

I am a highly skilled and experienced home service professional. I recently completed a job that involved seal and recharge of r-22 ac. The job required me to remove the old refrigerant from the system, clean the system, and then refill it with new refrigerant. I also had to test the system to ensure that it was working properly before leaving the job site.

I was called to inspect a residential air handler that was not working properly. Upon arrival, I observed that the unit was not producing any heat or air conditioning. I checked the electrical connections and found that one of the wires had come loose. I repaired the wire and tested the unit again. The air handler now produced heat and air conditioning. I tested the unit again to ensure it was working properly. I then cleaned the unit and made sure it was operating at peak efficiency.

Performed a residential furnace tune-up, including cleaning the burners, checking the ignition system, and adjusting the thermostat. Also, checked the air filter and replaced it if necessary.

I was hired to clean a mini split. I removed the front panel and cleaned the coils and fins. I also cleaned the air filter and evaporator. I used a brush and vacuum to clean the coils and fins. I used a coil cleaner to clean the air filter. I used a vacuum to clean the evaporator. I also checked the refrigerant levels and added more if needed.

I am a highly skilled HVAC contractor professional, and I recently completed an inspection on a residential AC unit. The inspection was conducted to identify any potential issues that could affect the unit's performance. During the inspection, I carefully examined the AC unit's components, including the compressor, condenser, evaporator, and ductwork. I also checked the refrigerant levels and pressure and tested the electrical connections. I found that the AC unit was operating normally, but I did notice some minor issues that could affect its efficiency. I recommended that the homeowner schedule a maintenance appointment to address these issues, including cleaning the evaporator coil, replacing the air filter, and checking the refrigerant levels. The homeowner was grateful for my thorough inspection and agreed to schedule the maintenance appointment. I am confident that the maintenance will help improve the AC unit's performance and extend its lifespan. Overall, performing an inspe

I am a highly skilled HVAC contractor professional. I recently completed a job where I performed a leak search on an AC unit. The AC unit was not cooling properly, and the customer suspected that there was a leak. I used a leak detection tool to locate the leak, which was a small pinhole leak in the refrigerant line. I repaired the leak and recharged the AC unit with refrigerant, and the customer was happy with the results.

I was called to a home to repair a tankless water heater. Upon arrival, I found that the unit was not producing hot water. I checked the power and gas supply and found that they were both working properly. I then checked the pressure relief valve and found that it was not working properly. I replaced the pressure relief valve and tested the unit again. The water heater was now producing hot water. I also checked the temperature and pressure relief valve for any leaks and found none. I then cleaned the unit and made sure that all the connections were tight. The customer was very happy with the service and thanked me for my help.

I am a highly skilled and experienced home service professional. I recently completed a job replacing a gas union on a water heater. The job required me to disconnect the old gas union, remove the old water heater, and install a new gas union and water heater. I also had to ensure that all connections were properly sealed and tested to meet safety standards. The job was completed on time and to the customer's satisfaction.

I was working as an HVAC contractor when I received a call to seal ductwork on a rooftop unit. The unit was located on the roof of a commercial building and had been experiencing issues with air leaks. I arrived at the site and inspected the ductwork. It was clear that the ductwork needed to be sealed to improve energy efficiency and prevent air leaks. I used a sealant gun to apply a sealant to the seams and joints of the ductwork. The sealant was a high-quality, durable material that would provide a long-lasting seal. I also made sure to clean up any debris that had accumulated on the ductwork before sealing it. After sealing the ductwork, I tested it to ensure that it was working properly. I was pleased to see that the air leaks had been eliminated, and the unit was now operating more efficiently. The customer was happy with the results and thanked me for my work.

I am a skilled professional that works for a McCarver Mechanical Heating & Cooling company. I was recently assigned to replace fuses on a disconnect for a condenser. The condenser is a component of a heating and cooling system that is used to remove heat from a building. To replace the fuses on the disconnect, I first turned off the power to the condenser. Then, I removed the cover from the disconnect and located the fuses. I carefully removed the old fuses and replaced them with new ones. I then turned on the power to the condenser and tested the new fuses to ensure they were working properly. It was a challenging job, but I was able to complete it successfully. I am proud of the work I did and the knowledge I gained from the experience.

I am a skilled professional that works for a McCarver Mechanical Heating & Cooling company. I recently completed a job where I performed maintenance on a mini split heat pump. The heat pump was not cooling properly, so I diagnosed the issue and replaced the compressor. I also checked the refrigerant levels and added more if needed. Finally, I tested the system to ensure it was working properly before completing the job.